- 1 Primer
- 2 General hints
- 3 Problems
- 4 Links/References
Several popular graphics cards out there - especiall NVIDIA ones - exhibit performance problems with KDE4. These performance hits mostly concern Plasma - the KDE4 desktop - and KWin - the KDE window-manager. Generally speaking this isn't due to KDE4 being unoptimized but a problem with the cards' graphics drivers. This page encompasses certain problems that might arise and how to get rid of them.
For both of the big graphics chip manufacturers there's 2 seperate graphics drivers each:
- For NVIDIA cards there's the free nv and the proprietary nvidia driver. While KDE4 should work fine with the former, it doesn't offer 3D acceleration, so the latter may be your only choice. All NVIDIA subsections herein only refer to the proprietary driver (there's also a 3rd free driver called nouveau that's currently being written. Unfortunately I don't know how usable it is so far). Due to licensing restrictions most distributions don't install the proprietary driver by default. Please refer to your distribution for information on how to install it.
It's usually advisable to stay up-to-date as improvements are being made in the drivers. Thus a first step in improving your KDE4 experience should be checking your current driver and updating if it's outdated. Please refer to your distribution's documentation on how to do that.
While it might further increase performance, I do NOT recommend installing beta quality drivers because your system's stability will most likely suffer.
Attributes set using the nvidia-settings utility aren't permanently saved. Thus you have to set them every time you restart your Xserver. This can be done conveniently by adding the lines to set the features to your ~/.xinitrc.
KDE4's systemsettings allows you to tweak some kwin settings as well. You can find the settings in Desktop -> Desktop Effects -> Advanced Options. Depending on your card either OpenGL or XRender might work better. For OpenGL changing the OpenGL mode might change performance as well. Please bear in mind that changing some of the tweaks mentioned below might force you to change your settings.
- Setting InitialPixmapPlacement to 2 might improve plasma's performance but might make kwin hang sometimes.
- Setting OpenGL mode to Shared Memory might make kwin more responsive again.
(note from a user)* Not selecting "Use Vsync" helped a lot in a gforce 6800
If for some reason your Xserver hangs after hitting the Apply button on the dialog and your settings get reverted because you can't confirm your changes in time, try again. Usually it will be faster on one of the subsequent tries. If it doesn't you can still change your settings in ~/.kde4/share/config/kwinrc.
This section summarizes several symptoms you might encounter and tries to explain possible causes.
Resizing certain windows is choppy
- This might be due to your card advertising ARGB Visuals (basically translucency) without having proper support for them. Applications/windows concerned are the plasma desktop, the krunner dialog (Alt+F2), plasma's Add new widget dialog or a konsole window.
- If you want to make sure this issue is a problem for you, run
$ XLIB_SKIP_ARGB_VISUALS=1 konsoleon the command-line and try to resize the new konsole window (setting the environment variable XLIB_SKIP_ARGB_VISUALS turns off ARGB visuals). If it resizes without problems, then this is certainly one of the problems you're facing.
- You can set the BackingStore options in your xorg.conf:
Section "Device" ... Option "BackingStore" "true" ... EndSection "Device"
This works for some (eg. konsole) but unfortunately not all windows.
- As a last resort you can try setting XLIB_SKIP_ARGB_VISUALS=1 in your ~/.xinitrc but this isn't pretty.
- You can set the IntialPixmapPlacement with the nvidia-settings utility:
$ nvidia-settings -a InitialPixmapPlacement=2This works for some (but unfortunately not all) NVIDIA cards.
Plasma performance is bad
- Unfortunately the reasons for plasma being choppy seem to be numerous so it's hard to tell where your choppiness comes from.
- Usually plasma performance problems can be seen best on the Folder View plasmoid. Moving it or scrolling inside the folder might be pretty slow.
- Please make sure this is not (only) related to the ARGB Visuals mentioned in the above section.
- You can set the IntialPixmapPlacement and the GlyphCache option with the nvidia-settings utility:
$ nvidia-settings -a InitialPixmapPlacement=2 -a GlyphCache=1This works for some (but unfortunately not all) NVIDIA cards. Some cards reportedly work better using InitialPixmapPlacement=1 (or maybe even 3)
- Options that are said to work well on 8xxx cards but are untested (by me)
- Option "RenderAccel" "True"
- enabled by default
- Option "TripleBuffer" "True"
- Enables triple buffering. "Decreases the time an application stalls while waiting for vblank events, but increases latency slightly" (NVIDIA Readme)
- Option "DamageEvents" "True"
- Recommended by NVIDIA if running composite+glx, increases performance, enabled by default
- Option "UseCompositeWrapper" "True"
- Enables the X server's composite wrapper instead of the builtin one.
- Option "AllowIndirectPixmaps" "True"
- Could improve hardware rendering on G80+ cards with more than 256 MB of video memory.
- Option "BackingStore" "True"
- Cache overlayed areas in case they get redisplayed later
- Option "PixmapCacheSize" "200000"
- allocate said number of pixels for pixmap caches
- Option "RenderAccel" "True"
Folder View and other plasmoids look badly rendered
- Folder View and some other plasmoids use hardware accelerated rendering. There are two methods to do this, and Plasma requires the newer EXA method.
- This is best seen on the Folder View widget, which will appear as a distorted and seemingly random region on the screen.
Open Source radeon driver
The Open Source radeon driver uses the older XAA hardware acceleration method. To work around this issue, you have to change the 2D acceleration method from XAA (X Acceleration Architecture) to the newer EXA. As this involves editing your xorg.conf file, bear in mind that such a modification may damage your system. Do it at your own risk.
To make the switch, edit your xorg.conf file (make a backup just in case) and locate the Device section for your graphics card. Add the line
Option "AccelMethod" "EXA"
before the "EndSection" line. If there is already a line with AccelMethod, change it from XAA to EXA. Save the file and restart the X server. Notice that EXA is still marked as unstable, and that some other applications such as some KDE3 programs may render incorrectly.
 -- Thread about graphics issues on the NVIDIA forums.